Premium Member 2and3cylinders Posted February 13, 2022 Premium Member Share Posted February 13, 2022 I'd still take it easy given you never got out of 2nd. Did you check valve lash? By "HOT", do you mean literally or figuratively? Meaning quick? I hope this is the last time you have to do something like this. Something I now will think long and hard about doing given your experience. Link to comment Share on other sites More sharing options...
redfjniner Posted February 13, 2022 Author Share Posted February 13, 2022 6 hours ago, 2and3cylinders said: I'd still take it easy given you never got out of 2nd. Did you check valve lash? By "HOT", do you mean literally or figuratively? Meaning quick? No, I did not check valve lash (clearance). It was shown that the engine only had 4,000 miles on it. I am assuming that was correct and will do a valve check at 15K, since these engines have shown that the exhaust valves get tight soon, as you have shown us with your more frequent checking. HOT as in the babe (hunk) walking down the street not as in McD's coffee. Anyway, I need to observe someone doing a valve check before I attempt it. I know, if I can remove and install an engine, make special tools, etc., I should be able to follow the manual and do a valve check. (and maybe a valve adjust too). 2 Ken, Candy Ass L.D.R. Sleeps 8 hours (2)2005 FJR1300abs: 230,000 m 2015 FJ-09: 114,000 m (Replaced engine at 106K) Link to comment Share on other sites More sharing options...
Premium Member 2and3cylinders Posted February 14, 2022 Premium Member Share Posted February 14, 2022 OK, 4k or not, I ass u me nothing and rarely trust anyone. I presume the cam chain sounds good. You can adjust it running... I've posted how recently. Link to comment Share on other sites More sharing options...
peteinpa Posted February 14, 2022 Share Posted February 14, 2022 Great Job! Glad I never had to do this and hope I never do. Valve check super easy, valve adjust whole other ball game. Link to comment Share on other sites More sharing options...
redfjniner Posted February 14, 2022 Author Share Posted February 14, 2022 (edited) 23 hours ago, 2and3cylinders said: OK, 4k or not, I ass u me nothing and rarely trust anyone. I presume the cam chain sounds good. You can adjust it running... I've posted how recently. I looked, but couldn't find your post. Give me a link. How to install APE CCT. Edited February 15, 2022 by redfjniner Add video. Ken, Candy Ass L.D.R. Sleeps 8 hours (2)2005 FJR1300abs: 230,000 m 2015 FJ-09: 114,000 m (Replaced engine at 106K) Link to comment Share on other sites More sharing options...
Supporting Member piotrek Posted February 15, 2022 Supporting Member Share Posted February 15, 2022 Strangely... APE website points to a thread at the FZ-09 forum. I installed mine with 9 exposed threads and went for a ride. Once warmed up, I pulled over and tweaked until the rattle became muted a bit, but not quite gone. It was easier to do with the stock exhaust. 1 Link to comment Share on other sites More sharing options...
Premium Member 2and3cylinders Posted February 15, 2022 Premium Member Share Posted February 15, 2022 Yep, I remove the cam chain cover too. With the valve cover off I check cam chain deflection between the cams (about 3/16") but if the valve cover is not off, the video is a good guide. By keeping tension on the cam chain with the side cover off, it's straight forward. When I need to remove the cams, after zip tiring the chain to the cam sprockets, I actually remove the tensioner slider to provide more slack so the cams can be moved clear of the buckets. With the cam chain tension close, warm up the engine until the fan comes on and then some, then with the engine still running, back off the lock nut and tensioner bolt until it just starts to gently rattle, then turn in the bolt until it JUST stops rattling and while restraining the bolt tighten but not too tight the lock nut. Then bring a 9/16" combo wrench and 4 mm hex wrench along on a decent ride and after a long hard pull, stop and recheck the adjustment. You'll occasionally notice a rattle or two, being very slightly loose is better than too tight IMO. GL! 2 Link to comment Share on other sites More sharing options...
redfjniner Posted March 6, 2022 Author Share Posted March 6, 2022 Good news. I was able to take the bike out yesterday for a 25 mile ride. This replacement engine has a slipper clutch. I can up shift with ease and no clutch, and easily down shift with a blip of the throttle. It will take a little getting used to, but Hey, I'm only 75 and learnable. 😊 2 1 Ken, Candy Ass L.D.R. Sleeps 8 hours (2)2005 FJR1300abs: 230,000 m 2015 FJ-09: 114,000 m (Replaced engine at 106K) Link to comment Share on other sites More sharing options...
Premium Member 2and3cylinders Posted March 7, 2022 Premium Member Share Posted March 7, 2022 I installed a 16 XSR900 slip/assist clutch and whereas my 15 has always shifted pretty slick it's not a dream (or as good as my VTR) but I've never really tried (maybe a couple of times) to downshift without the clutch... 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now